Products

Its high resistance to ultraviolet rays and its capacity to support weatherproof without losing its physical properties make SEAL 12-2 an ideal product to be applied on outdoor floors subject to a continuous traffic with industrial vehicles.

· Uses
· Surface preparation
· Instructions for use
· Consumption
· Colours
· Packing and storing
· Hygiene and safety
· Specification

Last update: 17/11/2008

Uses

SEAL 12-2 is a coating for indoor and outdoor concrete floors which need a high chemical and mechanical resistance. It is especially suitable for outdoor sport courts. SEAL 12-2 is also suitable to be applied by the multilayer system with the addition of silica sand which permits to obtain a thickness until 4 mm.

Surface preparation

The surface must be clean and dry and exempt of greases, oils and other pollutants which could affect the product adherence. It is recommended to scrape off or to mill the surface (with a milling machine or a “scrapping” machine) to achieve an open pore surface in order to facilitate a good adherence of the product. In old supports which have been painted before it is necessary to eliminate the remainders of paint and bad stuck particles.

Instructions for use

On new concrete or mortar surfaces apply a first coat with our primer PRIMA 68 and before the next 24 hours apply SEAL 12-2. To do this, mix the two components, pour component B completely into component A and mix them with a low revolutions mechanical mixer, adjust the viscosity with our solvent DILUYENTE Nº1 until a maximum of 15%. Let the mixture repose for 10 minutes before its application. SEAL 12-2 can be applied with brush, paint roller or air-less. The time to use the mixture is about 1 hour at 20ºC. Do not apply with temperatures below –10ºC.

Consumption

150-200 gr. per m² and coat, depending on the roughness of the surface.

Colours

Grey, red and green, other colours: on demand in orders over 500 Kg.

Packing and storing

SEAL 12-2 is supplied in hermetic barrels of 10 Kg. Part A:7.5 Kg. and Part B:2.5 Kg.
Professional use.

Hygiene and safety

See product label.

Specification

Aliphatic polyurethane resins, acetones and aromatic hydrocarbons and mineral stable to light pigments.
A/B mixture relation:3/1 in weight
Density:
Part A:1.45 ± 0.10 g/ml.
Part B:1.05 ± 0.03 g/ml.
Mixture A+B:1.30± 0.15 g/ml.
Dry extract:
Part A:71.0 ± 3.0%.
Part B:77.0 ± 3.0%.
Dry extract in volume:60% ± 3% depending on the colour.
Viscosity:
Part A (at 25ºC):25 ± 5P.
Part B (at 25ºC):45 ± 10P.
North Fineness:7.

Notes:

- La presente ficha técnica sirve, al igual que todas las demás recomendaciones e información técnica, únicamente para la descripción de las características del producto, forma de empleo y su aplicaciones. Los datos e informaciones reproducidas se basan en nuestros conocimientos técnicos obtenidos en bibliografia, en ensayos de laboratorio y en la práctica.
- Los datos sobre consumo y dosificación que figuran en esta ficha técnica se basan en nuestra propia experiencia, por lo que estos son susceptibles de variaciones debido a las diferentes condiciones de las obras. Los consumos y dosificaciones reales deberán determinarse en la obra mediante ensayos previos y son responsabilidad del cliente.
- Para un asesoramiento adicional, nuestro Departamento de Química Aplicada para la Construcción, está a su disposición.
- Otras aplicaciones del producto que no se ajusten a las indicadas, no serán de nuestra responsabilidad.
- Otorgamos garantía en caso de defectos en la calidad de fabricación de nuestros productos, quedando excluidas las reclamaciones adicionales, siendo de nuestra responsabilidad tan sólo la de reingresar el valor de la mercancía suministrada.
- Deben tenerse en cuenta las eventuales reservas correspondientes a patentes o derechos de terceros.
- La presente ficha técnica pierde su validez con la aplicación de una nueva edición.